KNOWING PLUMBING BASICS IS ESSENTIAL WHEN INSTALLING A BATHTUB

Knowing Plumbing Basics is Essential When Installing a Bathtub

Knowing Plumbing Basics is Essential When Installing a Bathtub

Blog Article

About This

Just how do you really feel on the subject of How to Install a Bathtub Yourself?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Setting up a tub isn't exactly brain surgery, however it does require strong plumbing, woodworking, and in some cases, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably hard task. If the old tub is readily available, the job can move rapidly; if you have to open up a wall to eliminate the old bathtub and also position the brand-new bathtub, the task is much harder. In either situation, the task is within a house handyman's abilities, although you will require an assistant to move out the old tub as well as embeded in the new one. Make certain you have actually certified on your own for the task and fit trying it. Instead of hiring a contractor to take control of a halfway-completed task, it is much better to consider utilizing one before you start. Possibilities are you may require a professional plumber to make tube links.
This post will help you install a brand-new tub in your shower room if you have currently gotten a brand-new bathtub and don't require to alter the arrangement of your previous water supply pipes.
Your tools as well as product checklist need to make up the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Planning for the Installation


    To start with, the supporting structure provided with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is necessary to see to it that if the faucet features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
    Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the provided washing machines.
    Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its last setting.

    Removing Old Taps


    If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is separate the water system. After doing so, activate the taps to drain any type of water staying in the system. The procedure of getting rid of the existing taps can be fairly bothersome as a result of the limited access that is typically the instance.
    Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a towel all set for the continuing to be water that will come from the pipelines. When the supply pipes have been gotten rid of, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from turning during this procedure. As soon as the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned up of any kind of old securing compound.
    Before moving on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

    Installing the Bathtub


    Making use of both wood boards under its feet, place the bath tub in the called for placement. The wooden boards are helpful in uniformly spreading out the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 little factors.
    The following objective is to ensure that the bathtub is leveled all round. This can be achieved by examining the spirit level and adjusting the feet on the bathtub until the spirit level reads level.
    To set up taps, fit the bottom of the outermost versatile tap port to the ideal supply pipeline by making a compression join; then do the very same for the various other faucet.
    Turn on the water supply and also examine all joints and new pipework for leaks and also tighten them if needed. Fill the bathtub as well as additionally inspect the overflow electrical outlet as well as the regular electrical outlet for leaks.
    Ultimately, fix the bathroom paneling as explained in the maker's user's manual. Tiling as well as securing around the bathtub must wait till the bath tub has been used at least when as this will settle it into its final setting.

    Suitable New Touches


    If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the various other end gives a link to the existing supply pipelines.
    If you require to fit a monobloc, after that you will certainly need lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
    Next off, position the tap in the mounting opening in the bath/basin making certain that the washers are in location in between the faucet and the sink. Safeguard the tap in position with the maker provided backnut. As soon as the faucet is safely in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind should be connected to the tap ends first, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been attached.

    Tiling Around the Bath tub


    In the area where the bathroom satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a stiff seal, triggering the water to permeate the wall surface between the bath as well as the tiling, resulting in problems with wetness and feasible leakages to the ceiling below.
    You can pick from a range of coloured sealers to assimilate your components and also installations. They are marketed in tubes as well as cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked newspaper or soft rope. Remember to constantly load the bath tub with water before securing, to enable the movement experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not take into account this activity prior to securing.
    Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly offered on the marketplace. It is a good idea to fit the tiles using water-resistant or waterproof glue as well as grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub Yourself

    I found that page on A Step-by-Step Guide to Installing a Bathtub when doing a search on the web. Be sure to take a moment to promote this blog post if you appreciated it. Bless you for your time. Kindly visit our blog back soon.


    Certified solutions offered.

    Report this page